SMT stencils | laser cut stencils | solder paste | circuit boards | printed circuit boards

Show All Categories

The greatest selection of SMT Stencils

Mylar and Kapton SMT Stencils

LEAD TIME : 24-Hour Turn

Price : $50.00

These are very low cost SMT Stencils specifically designed to manually print solder paste onto printed circuit boards.

Eliminates tedious hand soldering of prototype circuit boards
Lower cost than stainless steel stencils
Cut with a UV laser for optimal performance

We are backing that with a money-back guarantee program.

StencilQuik™ BGA Rework Stencils

LEAD TIME : 5 business days

Price : $74.00

StencilQuik™ are flexible solder paste stencils manufactured from a polyimide film with a high temperature adhesive covered with a release liner. They serve as both your stencil and alignment device.

StencilQuik comes in a pack of 10 BGA rework stencils
Allows you to replace your own BGAs or CSPs without special training or large capital equipment expenditures
Acts as an insulating barrier between solder balls as the solder paste masks adjacent apertures increasing placement reliability
Simplifies BGA placement as you can "feel" the device settle into the apertures of the StencilQuik™

StikNPeel™ Rework Stencils

LEAD TIME : Ships with 24-48 hours

Price : $80.00

StikNPeel™ greatly simplifies the ability to selectively print solder paste onto various areas of a PCB. Simply peel off the backing, place the StikNPeel™ onto the PCB and apply the paste.

StikNPeel comes in a pack of 10 stencils
This rework process overcomes many of the headaches of using metal stencils
Eliminates "smearing" of solder paste underneath the stencil
Co planarity between board and stencil is assured due to the adhesive backing on the stencil

Quick-Turn Rework Stencils

LEAD TIME : 24-Hour Turn

Price : $80.00

These laser cut stencils are typically used to manually print a single component on a printed circuit board.

Maximum Size 2" x 2"
Available with or without flaps (Flaps facilitate handling)
Mainly used for PCB rework but can used for prototype PCB assembly of simple boards

StencilMate™ Leadless Device Rework Stencils

LEAD TIME : 5 business days

Price : $80.00

Were designed to reliably and quickly replace leadless device packages such as QFNs or LGA packages.

StencilMate™ comes in a pack of 20 rework stencils
Alignment is simple. No need to use custom fixtures or frames.
The stencil is cut using a laser to your exacting device requirements.
Elimnate the need to use capital intensive equipment or require a high degree of skill.

Flip-Up Stencils

LEAD TIME : 3-5 Days

Price : $89.00

Flip-Up Stencils are single site stencils, used to apply solder paste onto circuit board pads of BGA’s, QFN’s, QFP’s, TSOPS, PLCC’s, etc.

Great for QFN’s where the pads on the board are larger than the pads on the component.
All Flip Up stencils are made from stainless steel and are reusable after a quick wash in an alcohol based cleaner.
All Flip Up stencils are custom made to order per your specification.

Prototype SMT Stencils

LEAD TIME : 24-Hour Turn

Price : $125.00

These frameless SMT stencils are specifically designed to manually print solder paste onto printed circuit boards.

Eliminates tedious hand soldering of prototype circuit boards
Reduce PCB prototype assembly time
Available with or without flaps

** The stencil kit comes with a squeegee blade and board holders.
** Our process using a Toaster Reflow Oven will make your prototype PCB assembly job easier and save you time.
** We are backing that with a money-back guarantee program.

CPF Stencils

LEAD TIME : 3-5 Days

Price : $135.00

CPF Stencils (or Component Print Frame) are used to apply solder paste directly onto BGA and Leadless components.

A CPF stencil makes for simple alignment when pasting, and serves as an excellent tool for applying paste when boards are highly populated.
All CPF stencils are made from stainless steel and are reusable after a quick wash in an alcohol based cleaner.
All CPF stencils are custom made to order per your specification.

* Order contain stencil only. Please see accesories

Frameless SMT Stencils

LEAD TIME : 24-Hour Turn

Price : $150.00

These laser cut stencils are designed to work with stencil tensioning systems also known as Reusable Stencil Frames like the Wizard Frame.

Reduces storage space requirements
Significantly less expense than framed stencils
Smooth aperture walls and can be used for 16 Mil pitch and below and for Micro BGA"s

** Framelss SMT Stencils are recommended for prototype printed circuit board assembly or short runs.

Framed SMT Stencils

LEAD TIME : 24-Hour Turn

Price : $185.00

These solder paste stencils are designed for high volume screen printing on printed circuit boards.

Foils are permanently mounted into aluminum frames
Provide optimum solder paste volume control
Large variety of standard frames for every printer

** Framed stencils have smooth aperture walls and can be used for 16 Mil pitch and below and for Micro BGA"s.

Framed Multi-level / Step Stencils

LEAD TIME : 48-Hour Turn

Price : $185.00

These Multi-level Stencils offer superior flexibility in achieving the right solder paste volume deposit for components with diverse paste requirement.

Provide optimum solder paste volume control
Eliminate co-planarity problems
Foils are permanently mounted into aluminum frames

Framed UltraSlic™ Stencils

LEAD TIME : 48-Hour Turn

Price : $375.00

An alternative to Electroform Stencil, UltraSlic™.

UltraSlic™ FG outperforms all other existing stencil technologies on the market today, and it can be shipped in 48 hours turnaround times.

Fine Grain stainless steel with superior fatigue strength, super smooth surface and elevated wear factor
Superior paste release below surface area ratios of 0.5
Higher performance and lower cost compared to electroform, the option of step stencils

Framed Electroformed Stencils

LEAD TIME : 48-Hour Turn

Price : $475.00

Electroformed stencils offer the best paste release characteristics available and are frequently used for fine pitch (20 mil to 12 mil pitch) SMT applications on printed circuit boards. They are also used for µBGA's, Flip Chip, and Wafer Bumping (12 mil to 6 mil pitch).

The smooth trapezoidal sidewalls of an electroformed stencil allow for better paste release
Nickel has a lower coefficient of friction compared to stainless steel
Electroform foils are harder than full hard stainless steel of comparable thickness, providing for longer stencil life